|
Question |
Rating |
View Answer |
|
Which three are benefits of IS-IS over OSPF? (Choose three.) A. supports more routers in an area B. does not require Hello packets to establish neighbor relationships C. produces fewer link state advertisements for a given network D. supports route tags E. supports network layer protocols other than IP F. requires fewer neighbor relationships in a broadcast multiaccess network
|
|
View Answer |
|
What is IPv6 router solicitation? A. a request made by a node for the IP address of the local router B. a request made by a node for its IP address C. a request made by a node for the IP address of the DHCP server D. a request made by a node to join a specified multicast group
|
|
View Answer |
|
In a comparison of an IPv4 header with an IPv6 header, which three statements are true? (Choose three.) A. An IPv4 header includes a checksum. However, an IPv6 header does not include one. B. A router has to recompute the checksum of an IPv6 packet when decrementing the TTL. C. An IPv6 header is half the size of an IPv4 header. D. An IPv6 header has twice as many octets as an IPv4 header. E. An IPv6 header is simpler and more efficient than an IPv4 header. F. The 128-bit IPv6 address makes the IPv6 header more complicated than an IPv4 header.
|
|
View Answer |
|
An administrator has decided to configure Integrated IS-IS on the network. What must the administrator do to enable the interfaces to distribute IP information using IS-IS? A. The networks configured on each interface must be associated to the IS-IS routing protocol using the network router configuration command. B. Each interface must be enabled to support IS-IS with the ip router isis interface configuration command. C. All configured IP networks will automatically be enabled when IS-IS is configured with the router isis global configuration command. D. Each network must be identified with the net interface configuration command.
|
|
View Answer |
|
Which statement is true about the command ipv6 ospf 1 area 0? A. It must be issued in router global configuration mode to enable the OSPF process for IPv6. B. It must be issued in interface configuration mode to enable the OSPF process for IPv6. C. It must be issued before the network command to enable the OSPF process for IPv6. D. It must be issued after the network command to enable the OSPF process for IPv6.
|
|
View Answer |
|
Which three statements are true about IP multicast configuration? (Choose three.) A. PIM sparse mode interfaces are always added to the multicast routing table in a router. B. PIM dense mode interfaces are always added to the multicast routing table in a router. C. PIM sparse-dense mode acts as PIM dense mode if an RP is not known. D. PIM sparse-dense mode and PIM dense mode require an RP on the network. E. PIM sparse mode and PIM sparse-dense mode require an RP on the network. F. PIM sparse mode and PIM dense mode require an RP on the network.
|
|
View Answer |
|
What are two rules for compacting IPv6 addresses? (Choose two.) A. The maximum number of times a double colon can replace a 16-bit segment that consists of all zeroes is two. B. The leading zeroes in any 16-bit segment do not have to be written. C. Every 16-bit segment segment that consists of all zeroes can be represented with a single colon. D. The trailing zeroes in any 16-bit segment do not have to be written. E. Any single, continuous string of one or more 16-bit segments that consists of all zeroes can be represented with a double colon. F. Two zeroes in the middle of any 16-bit segment do not have to be written.
|
|
View Answer |
|
A network administrator has enabled OSPF across an NBMA network and has issued the command ip ospf network nonbroadcast. Given those facts, which two statements are true? (Choose two.) A. DR and BDR elections will occur. B. DR and BDR elections will not occur. C. All routers must be configured in a fully meshed topology with all other routers. D. The neighbor command is required to build adjacencies. E. Interfaces will automatically detect and build adjacencies with neighbor routers.
|
|
View Answer |
|
Which two statements are true about the rendezvous point (RP) in a multicast network? (Choose two.) A. An RP is required only in networks running Protocol Independent Multicast dense mode (PIM DM). B. An RP is required only in networks running Protocol Independent Multicast sparse mode (PIM SM). C. An RP is required only in networks running Protocol Independent Multicast sparse-dense mode (PIM-SDM). D. The multicast sources must register with the RP to form the multicast distribution tree. E. The multicast receivers must register with the RP to form the multicast distribution tree. F. To form the multicast distribution tree, the multicast sources register with and the receivers join the RP.
|
|
View Answer |
|
According to RFC 2328, what is the stateful order in which an OSPF router transitions to a full adjacency with a neighbor router? A. Down, Init, 2-Way, Exchange, Exstart, Loading, and Full B. Down, Init, 2-Way, Exstart, Exchange, Loading, and Full C. Down, Init, 2-Way, Loading, Exstart, Exchange, and Full D. Down, 2-Way, Init, Exchange, Exstart, Loading, and Full E. Down, 2-Way, Init, Exstart, Exchange, Loading, and Full F. Down, 2-Way, Init, Loading, Exstart, Exchange, and Full
|
|
View Answer |
|
Which two statements about the IS-IS routing protocol are true? (Choose two.) A. In the IS-IS routing domain, routers may have adjacencies with other routers on multipoint links. B. IS-IS metrics are based on delay, bandwidth, reliability, load, and MTU. C. Level 1 routers learn about paths within the areas that the routers are connected to. D. Level 2 routers are equivalent to ABRs in OSPF and learn about paths both within and between areas. E. Level 1 and Level 2 routing is a function of ES-IS.
|
|
View Answer |
|
In an IS-IS environment, what happens when the designated IS router crashes? A. The elected backup designated router takes the place of the DIS indefinitely without the necessity of a new election. B. The elected backup designated router takes the place of the DIS temporarily without the necessity of a new election, until the original DIS comes back online. C. A new election process occurs immediately, establishing a new DIS that will remain in place indefinitely. D. A new election process occurs immediately, establishing a new DIS until a router with a higher priority or MAC address establishes an adjacency.
|
|
View Answer |
|
Which three route filtering statements are true? (Choose three.) A. After the router rip and passive-interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interface. B. After the router eigrp 10 and passive-interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interface. C. After the router ospf 10 and passive-interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interface. D. When you use the passive-interface command with RIPv2, multicasts are sent out the specified interface. E. When you use the passive-interface command with EIGRP, hello messages are not sent out the specified interface. F. When you use the passive-interface command with OSPF, hello messages are not sent out the specified interface.
|
|
View Answer |
|
A network engineer wants to configure a large Frame Relay network. The desired topology is full mesh. Assume that n denotes the number of router endpoints in the topology. What formula should be used to determine how many PVCs to configure? A. 2*n B. 3*n C. n*n D. n*(n-1) E. n*(n+1)/2 F. n*(n-1)/2
|
|
View Answer |
|
Which of the three areas below are valid OSPF area types? (Select three)
A. Stub B. Active C. Remote D. Backbone E. Ordinary or standard
|
|
View Answer |
|
A network administrator is troubleshooting an EIGRP configuration across a discontiguous network. What must the administrator do to ensure the routers have the correct routing information?" A. Nothing, EIGRP supports discontiguous networks by default. B. The administrator must disable automatic summarization with the command no auto-summary. C. The administrator must enable manual summarization with the command ip summary-address. D. The administrator must enable classless routing with the command ip classless. E. The administrator must specify a default network with the command ip default-network.
|
|
View Answer |
|
A network administrator is troubleshooting an EIGRP configuration across a discontiguous network. What must the administrator do to ensure all of the PassGuide routers have the correct routing information?
A. The administrator must enable classless routing with the command “ip classless” B. The administrator must disable automatic summarization with the command “no auto-summary” C. The administrator must specify a default network with the command “ip default-network” D. Nothing, EIGRP supports discontiguous networks by default. E. The administrator must enable manual summarization with the command “ip summary-address” F. None of the other alternatives apply
|
|
View Answer |
|
Which two statements are true about 6to4 tunnels? (Choose two.) A. In a 6to4 tunnel, the first two bytes of the IPv6 address will be 0x2002 and the next four bytes will be the hexadecimal equivalent of the IPv4 address. B. In a 6to4 tunnel, the first two bytes of the IPv6 address will be locally derived and the next two bytes will be the hexadecimal equivalent of the IPv4 address. C. In a 6to4 tunnel, the IPv4 address 192.168.99.1 would be converted to the 2002:c0a8:6301::/48 IPv6 address. D. In a 6to4 tunnel, the IPv4 address 192.168.99.1 would be converted to the 2002:c0a8:6301::/16 IPv6 address. E. In a 6to4 tunnel, the IPv4 address 192.168.99.1 would be converted to the 2002:1315:4463:1::/64 IPv6 address.
|
|
View Answer |
|
Which statement describes the difference between a manually configured IPv6 in IPv4 tunnel versus an automatic 6to4 tunnel? A. A manually configured IPv6 in IPv4 tunnel allows multiple IPv4 destinations. B. An automatic 6to4 tunnel allows multiple IPv4 destinations. C. A manually configured IPv6 in IPv4 tunnel does not require dual-stack (IPv4 and IPv6) routers at the tunnel endpoints. D. An automatic 6to4 tunnel does not require dual-stack (IPv4 and IPv6) routers at the tunnel endpoints.
|
|
View Answer |
|
A network administrator assigns a multicast address of 239.255.8.5 to an application running on a device with an Ethernet MAC address of 01.b2.7d.05.f1.80. Which Layer 2 multicast address will this device use? A. 01.00.5e.7F.08.05 B. 01.b2.7d.05.f1.80 C. 01.b2.7d.0a.08.05 D. 01.00.5e.05.f1.80 E. ff.ff.ff.ff.ff.ff
|
|
View Answer |