On which of the following voltage range settings will a voltmeter present the minimum load on a circuit? A. 1 V B. 50 V C. 500 V D. 1,000 V

CoolInterview.com - World's Largest Collection of Interview Questions

Sponsored Links

Interview Questions

Our Services

Get 9,000 Interview Questions & Answers in an eBook.

9500+ Pages
9000 Question & Answers
All Tech. Categories

14 MB Content

Get it now !!

INTERVIEW QUESTIONS ELECTRICAL & ELECTRONICS ENGINEERING(EEE) DETAILS

Question :
On which of the following voltage range settings will a voltmeter present the minimum load on a circuit?
A. 1 V
B. 50 V
C. 500 V
D. 1,000 V

Category Electrical & Electronics Engineering(EEE) Interview Questions

Rating (0.4) By 13 users

Added on 6/17/2011

Views 154

Rate it!

Answers:

Option D

If you have the better answer, then send it to us. We will display your answer after the approval.
Rules to Post Answers in CoolInterview.com:-
There should not be any Spelling Mistakes.

There should not be any Gramatical Errors.

Answers must not contain any bad words.

Answers should not be the repeat of same answer, already approved.

Answer should be complete in itself.

Name :*

Email Id :*

Answer :*

Verification Code Not readable? Load New Code

Enter the above shown code:*

Inform me about updated answers to this question

Related Questions View Answer

A certain Wheatstone bridge has the following resistor values: RV = 10 k, R2 = 720 , and R4 = 2.4 k. The unknown resistance is
A. 24
B. 2.4
C. 300
D. 3,000 View Answer

The parallel combination of a 470 resistor and a 1.5 k resistor is in series with the parallel combination of five 1 k resistors. The source voltage is 50 V. The percentage of the load current through any single 1 k resistor is
A. 25% B. 20%
C. 100% D. 50% View Answer

Referring to Problem 24, the voltage across the 1.5 k resistor is approximately
A. 1.8 V
B. 18 V
C. 3.2 V
D. 32 V View Answer

Three 10 k resistors are connected in series. A 20 k resistor is connected in parallel across one of the 10 k resistors. The voltage source is 24 V. The total current in the circuit is
A. 900 A
B. 9 mA
C. 90 mA
D. 800 A View Answer

A voltage divider consists of two 68 k resistors and a 24 V source. The unknown output voltage is
A. 12 V
B. 24 V
C. 0 V
D. 6 V View Answer

A certain voltage divider consists of two 12 k resistors in series. Which of the following load resistors will have the most effect on the output voltage?
A. 1 M
B. 24 k
C. 18 k
D. 12 k View Answer

The output of a certain voltage divider is 12 V with no load. When a load is connected, the output voltage
A. decreases
B. increases
C. remains the same
D. becomes zero View Answer

Two 1.2 k resistors are in series and this series combination is in parallel with a 3.3 k resistor. The total resistance is
A. 138
B. 1,389
C. 5,700
D. 880 View Answer

The internal resistance of a 20,000 ohm/volt voltmeter set on its 5 V range is
A. 20,000
B. 100,000
C. 200,000
D. 1,000,000 View Answer

What is the voltage gain of voltage follower? View Answer

If the voltage across a resistor is doubled what will the current be? View Answer

What is the current through a 1.5k resistor with voltage of 3V across it?

View Answer

What is the conversion from RMS voltage to peak voltage?

View Answer

How do i Calculate leakage current from leakage voltage

View Answer

A 12 mA current source has an internal resistance, RS, of 1.2 k. The equivalent voltage source is
A. 144 V
B. 14.4 V
C. 7.2 V
D. 72 mV View Answer

A 120 load is connected across a voltage source with VS = 12 V and RS = 8 . The voltage across the load is
A. 11.25 V
B. 0 V
C. 12 V
D. 1.13 V View Answer

A 120 load is connected across an ideal voltage source with VS = 12 V. The voltage across the load
A. is 0 V
B. is 12 V
C. is 120 V
D. cannot be determined View Answer

A certain voltage source has the values VS = 30 V and RS = 6 . The values for an equivalent current source are
A. 5 A, 6
B. 30 A, 6
C. 5 A, 30
D. 30 A, 5 View Answer

An 18 V source has an internal resistance of 70 . If a load resistance of 33 is connected to the voltage source, the load power, PL, is
A. 0 W
B. 1 W
C. 175 mW
D. 18 mW View Answer

A 2 RL is connected across a voltage source, VS, of 110 V. The source's internal resistance is 24 . What is the output voltage across the load?
A. 8.5 V
B. 85 V
C. 0 V
D. 110 V View Answer

Please Note: We keep on updating better answers to this site. In case you are looking for Jobs, Pls Click Here Vyoms.com - Best Freshers & Experienced Jobs Website.
View ALL Electrical & Electronics Engineering(EEE) Interview Questions