CoolInterview.com - World's Largest Collection of Interview Questions
Start Your Own website Now
Sponsored Links

Interview Questions
Our Services

Get 9,000 Interview Questions & Answers in an eBook.


  • 9500+ Pages
  • 9000 Question & Answers
  • All Tech. Categories
  • 14 MB Content

    Get it now !!



    Send your Resume to 6000 Companies


  • INTERVIEW QUESTIONS SCIENCE METALLURGY DETAILS
    Question :
    How to calculate heat affected zone in weld?
    Category Metallurgy Interview Questions
    Rating (0.4) By 734 users
    Added on 9/24/2009
    Views 1500
    Rate it!
    Answers:

    Heat affected zone is measured regarding the microstructure changes in the weld. For example in steels, this is the area around the weld zone, which has undergone a transformation. In other words, this is the area, which had been austenitized. For calculating the HAZ after welding, for steels, it is better to macroetech the section of the weld HAZ can be easily recognized by the contrast it makes with the base metal and the weld metal.



    If you have the better answer, then send it to us. We will display your answer after the approval.
    Rules to Post Answers in CoolInterview.com:-

  • There should not be any Spelling Mistakes.
  • There should not be any Gramatical Errors.
  • Answers must not contain any bad words.
  • Answers should not be the repeat of same answer, already approved.
  • Answer should be complete in itself.
  • Name :*
    Email Id :*
    Answer :*
    Verification Code Code Image - Please contact webmaster if you have problems seeing this image code Not readable? Load New Code
    Process Verification  Enter the above shown code:*
    Inform me about updated answers to this question

       
    Related Questions
    View Answer
    Why is it so hard to find literature on the wear resistance of titanium?
    View Answer
    Is it possible to use metallurgical inverted microscope to other designation?
    View Answer
    When using mercury to recover very, fine gold from ore, what is the best way to separate the gold laden mercury from the ore?
    View Answer
    Is there any way through hardening and anodizing some type of aluminum, it could be as hard as steel? I have hardened steel rollers that run up and down on a ramp along with spring pressure. Alternatively, if you are familiar with snowmobiles, the rollers run on the helix on the secondary clutch.
    View Answer
    What is the minimum temperature for stress relieving of ASTM A 519 Gr.4130 material and please tell us where we can find the location.
    View Answer
    What are Metallurgical microscopes?
    View Answer
    Is there a possibility of inducing stress cracking in an insulated stainless road tanker vessel (20 tonne capacity) if the vessel is subject to rapid filling (10 tonne /hr) with liquid methane (-160 C) assuming the vessel is at ambient. If so, where could I obtain suggested cooling rates?
    View Answer
    What metal cord transfers electricity, and how can i tell?
    View Answer
    What is meant by hardening ability of metals?
    View Answer
    Can 1026 steel be welded?
    View Answer
    What is the chemical composition of ceramic and what is its atomic density?
    View Answer
    Which of different types of cast irons is stronger? Is their strength superior to steels?
    View Answer
    How one can differentiate between 304 & 316 grades of Steel (Physically)?
    View Answer
    What is the melting point of E70 steel, 304,308,316 stainless steels? In addition, what is the hottest part of the flame in a fire?
    View Answer
    How is metal heavy?
    View Answer
    Does case harden steel properties detoriates over time? Especially for guns, parts like bolt carrier, the brand new parts has been kept for 10 year and properly oiled. I am worried about its surface hardness to take the blow during firing.
    View Answer
    Does the extrusion process for A355 AND A356 alloy effect on the amount of impact energy?
    View Answer
    What is the difference between plaster used in gold investment casting and ceramic used in the process of investment casting of automobile engine parts and turbine blades etc. when both are used in the lost-wax method?
    View Answer
    We make aluminum moulds by press casting, can u suggest any thing so that the moulds should shine after casting?
    View Answer
    What is the grain size of lead as an element and as an alloy such as lead tin alloy?
    View Answer


    Please Note: We keep on updating better answers to this site. In case you are looking for Jobs, Pls Click Here Vyoms.com - Best Freshers & Experienced Jobs Website.

    View ALL Metallurgy Interview Questions

    User Options
    Sponsored Links


    Copyright ©2003-2014 CoolInterview.com, All Rights Reserved.
    Privacy Policy | Terms and Conditions

    Download Yahoo Messenger | Placement Papers| FREE SMS | ASP .Net Tutorial | Web Hosting | Dedicated Servers | C Interview Questions & Answers

    Testing Articles | Testing Books | Testing Certifications | Testing FAQs | Testing Downloads | Testing Interview Questions | Testing Jobs | Testing Training Institutes


    Cache = 0.015625 Seconds